Home › Guides › Water-damaged key fob
Key fob dropped in water: what to do
Through the washing machine, into the sea, down the toilet, or a day in a wet coat pocket. What you do in the first ten minutes decides whether this is a dry-out or a new key.
Right now, in this order
- Don't press any buttons. Pressing a button on a wet board pushes current across the water and that's what does the damage. Fresh water alone, with no power through it, is mostly harmless.
- Open the fob and take the battery out. Use the slot or seam, not a knife. If there's a mechanical blade, pull or release it so the case comes fully apart. Flip keys: the board comes out with the hinge; keyless fobs: lift the back cover and the board follows.
- Rinse if it was anything but clean water. Sea water, dishwasher water, washing-machine water with detergent in it, toilet water — all leave residue that keeps conducting and corroding after the fob is dry. Rinse the bare board under a gentle run of fresh tap water (yes, really), or better, isopropyl alcohol if you have it. Don't rinse the transponder chip if it's a glass tube — just dry it.
- Shake and blot. Shake the board to throw water out from under the components, then blot with kitchen roll. Cotton buds get into the battery clip and the switch domes.
- Dry with moving air, not heat. A warm, airy spot — on top of the fridge, in an airing cupboard, in front of a fan — for 24 hours. No hair dryer on hot, no radiator, no oven. Heat softens the plastic, lifts the conformal coating on the board and can pop the glass transponder.
- Leave the rice in the cupboard. Rice doesn't pull water out of a sealed fob; it adds starch dust to the contacts. Silica gel sachets in a sealed bag do help, if you have a handful.
- Reassemble with a new battery — the old one has been shorted and won't be reliable — and test. If the remote works, press every button twenty times over the next day to be sure the switches haven't started corroding.
Why the car will probably still start
The part that lets the engine start — the transponder chip — is a sealed glass tube or a potted block with no battery and no moving parts. It shrugs off water. So even if the remote is a write-off, the key will almost always still turn the ignition and start the car once it's dry. That buys you time: you're not stranded, you've just lost remote locking until it's fixed. The exception is a keyless (proximity) fob, which needs its own power to be found by the car; a drowned keyless fob can leave you with a car that won't start until you use the backup spot — see dead fob: how to get in and start.
What usually survives, what usually doesn't
| What happened | Outlook |
|---|---|
| Rain, a puddle, a wet pocket for an hour | Nearly always fine once dry. The battery clip may need cleaning. |
| Washing machine, full cycle | Usually survives if the battery comes out straight away and the board is rinsed and dried. Detergent residue is the enemy — rinse it. |
| Tumble dryer as well | Worse: heat plus moisture. Cases warp, pads go sticky, boards sometimes delaminate. Often repairable, sometimes not. |
| Fresh water — river, lake, bath, toilet | Good odds if dried promptly. Toilet water needs a proper rinse. |
| Sea water | The worst. Salt keeps conducting and eats copper tracks within days. Rinse in fresh water immediately, then alcohol, then dry. Get it looked at within the week even if it seems to work. |
| Left wet for days before anyone noticed | Green corrosion on the clip and the switch domes. Sometimes cleanable, often a board transfer or a new remote. |
What the damage looks like later
- Short range or a dead remote weeks after it dried — corrosion creeping across a track or under a component.
- One button failing after another — the switch domes rust from the inside.
- Battery lasting a month — a corroded path is drawing current all the time.
- Buttons sticky or the case cloudy — heat damage from drying it too hard.
All of these are the fob telling you the rinse-and-dry only half worked. They're usually fixable, but sooner is better than later.
What we do
We strip the fob, clean the board ultrasonically or with alcohol, replace corroded switches and clips, re-solder anything the water has lifted, fit a new battery and a new case or pad if the old one has warped, and test it on the car. If the board is beyond saving, the transponder chip is almost always still good, so a new remote is programmed and the chip moved across — a smaller job than a full key from scratch. If the chip has gone too, we make a new key at the car. Fob repair → · Replacement fobs →
Common questions
My fob went through the wash and still works. Do I need to do anything?
Change the battery, and keep an eye on range and buttons over the next month. If either fades, there's residue on the board and it wants cleaning before it corrodes.
Can I put the fob in rice?
It won't hurt, but it does almost nothing — the water is inside a closed case the rice can't reach. Take the battery out and let air do the work.
The remote is dead but the car starts. Do I need a new key?
Usually not. The remote board is repaired or replaced and your transponder chip — the part that starts the car — stays. Programming is only needed if the remote is replaced.
Is a keyless fob worse than a normal key if it gets wet?
A little. It has a bigger board and the car can't find it without power, so a drowned one can stop you driving until it's dried or replaced. The backup spot in the car gets you going meanwhile.
Call 07958 169 595 WhatsApp us
Open 24/7 · All major makes · We come to you · More guides