Home › Guides › Fob buttons not working
Key fob buttons not working
The unlock button needs three presses, the boot button does nothing, or the whole fob has gone quiet. Which buttons have failed tells you most of what you need to know.
One button dead, the rest fine
That's a mechanical fault in that button, and it's the most common fob repair there is. Under each rubber button is a tiny micro-switch — a metal dome soldered to the board that clicks when pressed. They're rated for a few hundred thousand presses, which sounds like a lot until you work out that the unlock button on a daily driver gets pressed two or three thousand times a year, often with a thumbnail. The switch wears, the click goes soft, the button needs pressing harder and harder, then it stops. The rubber pad wears too: the button sinks, the printing rubs off, and eventually the rubber splits so the switch underneath gets pressed by nothing.
Both are repairable without touching the programming. A worn switch is unsoldered and a new one fitted; a worn pad is replaced, usually along with the case if that's cracked. Your transponder chip and remote board stay as they are, so the car never knows anything happened. Fob repair →
All the buttons dead, car still starts
Work down this list:
- Battery — flat, wrong thickness, in backwards, or film still on. The battery guide →
- Lost sync — the car and remote have fallen out of step, often after a battery change or a flat car battery. Some makes need a re-sync sequence; it's in the same guide.
- Cracked solder joint — the fob works if you squeeze it, or worked intermittently for weeks before stopping. Repairable.
- Water — a trip through the washing machine or a wet pocket. See the water-damage guide; speed matters.
- The remote board itself — rarely, the transmitter chip fails. Then it's a replacement remote programmed to the car.
Try the spare first. If the spare works normally, the car is fine and the fault is in the fob.
Buttons dead and the car won't start
Two separate systems have failed at once, which usually means a shared cause: the fob has been crushed, soaked or run over, or the car's battery is flat. The remote and the transponder don't otherwise share anything — the transponder has no battery and no buttons — so if the engine won't turn over at all, check the car battery before blaming the key. If the car cranks but won't fire and the immobiliser light is flashing, the transponder isn't being read: a chip broken in the fob, or the key has dropped out of the car's memory. That's a programming or replacement key job.
A button that works but does the wrong thing
Lock locks, unlock locks again, the boot button opens the doors. That's a pad that's shifted inside the case so the rubber is pressing the wrong dome, or a split pad pressing two at once. A new pad, properly seated, fixes it.
"I'll just buy a new case online and swap it myself"
You can, and plenty of people do. The things that go wrong:
- The transponder chip — a glass tube or a small black block in the head of the key — doesn't get moved across, or gets moved and cracked. Without it the car won't start, and a chip can't be repaired, only replaced and re-programmed.
- The new case doesn't fit the board: the buttons sit in the wrong place, the battery clip doesn't reach, the blade is the wrong profile or the hinge is a different design. Fobs that look identical in a listing often aren't.
- The blade needs cutting. A new flip-key case comes with a blank, which has to be cut to your locks on a proper machine — the worn original can't be used as a pattern with any accuracy.
- The board is damaged getting it out of the old case — the solder joints on an old fob are brittle.
If you want to do it yourself, do it with the car outside, the spare key in your pocket and a magnifying glass to hand. If you'd rather not, we do the whole thing at the car in about twenty minutes, blade cut and tested. Fob repair →
What we do
We open the fob properly, check the switches and the pad, test the board, and fit new switches or a new case and pad with your own electronics transferred. If the board is beyond saving, we say so and supply a replacement remote programmed to the car. Either way it's done at the car and tested on every door before we leave. Fob repair → · Replacement fobs →
Common questions
Can the buttons be fixed or do I need a new key?
Fixed, nearly always. Worn switches and pads are replaced with your chip and board kept, so there's no programming and the car isn't involved.
The buttons work but I have to press really hard.
Worn micro-switches. They'll fail completely in time; a switch replacement now is quicker than a dead fob later.
Only the boot button has stopped. Does it matter?
Only if you use it. It's the same switch repair as any other button, and you can live without it until the next thing needs doing.
I swapped the case and now the car won't start.
The transponder chip is still in the old case, has fallen out, or has cracked. Check the old case for a small glass tube or black block. If it's intact, we transfer it; if it's broken, a new key is programmed to the car.
Call 07958 169 595 WhatsApp us
Open 24/7 · All major makes · We come to you · More guides